- 694 - ac .442(11.23) .432(10.97) .25(6.35) .22(5.59) .20(5.08) hole for #10 screw dia .692(17.6) .612(15.5) 1.14(29.0) 1.12(28.5) 1.14(29.0) 1.12(28.5) .692(17.6) .612(15.5) .602(15.3) .522(13.3) .752(19.1) .672(17.1) .96(24.5) .85(21.5) .490(12.4) .410(10.4) .442(11.23) .432(10.97) .042(1.07) .038(0.97) .22(5.59) .20(5.08) hole for #10 screw dia 1.14(29.0) 1.12(28.5) .752(19.1) .672(17.1) .752(19.1) .672(17.1) 1.14(29.0) 1.12(28.5) 1.2(30.5) min. .692(17.6) .612(15.5) .034(0.86) .030(0.76) 0.442(11.23) 0.432(10.97) .26(6.60) .22(5.59) .20(5.08) hole for #10 screw dia .692(17.6) .612(15.5) .692(17.6) .612(15.5) .692(17.6) .612(15.5) 1.14(29.0) 1.12(28.5) 1.14(29.0) 1.12(28.5) 0.967(24.57) 0.837(21.26) gbpc 15, 25, 35 series high current 15, 25, 35 amps. single phase glass passivated bridge rectifiers voltage range 50 to 1000 volts current 15.0/25.0/35.0 amperes features ul recognized file # e-96005 the plastic material used carries underwriters laboratory flammability recognition 94v-0 integrally molded heatsink provide very low thermal resistance for maximum heat dissipation surge overload ratings from 300 amperes to 400 amperes terminals solderable per mil-std-202, method 208 (for wire type) typical i r less than 0.2 ua high temperature soldering guaranteed: 260 / 10 seconds / .375?, (9.5mm) lead lengths(for wire type) isolated voltage from case to lead over 2500 volts gbpc gbpc-w gbpc-m dimensions in inches and (millimeters) maximum ratings and electrical characteristics rating at 25 ambient temperature unless otherwise specified. single phase, half wave, 60 hz, resistive or inductive load. for capacitive load, derate current by 20% type number symbol -005 -01 -02 -04 -06 -08 -10 units maximum recurrent peak reverse voltage v rrm 50 100 200 400 600 800 1000 v maximum rms voltage v rms 35 70 140 280 420 560 700 v maximum dc blocking voltage v dc 50 100 200 400 600 800 1000 v maximum average forward gbpc15 rectified current gbpc25 @t c = 55 gbpc35 i (av) 15.0 25.0 35.0 a peak forward surge current, gbpc15 single sine-wave superimposed gbpc25 on rated load (jedec method ) gbpc35 i fsm 300 300 400 a maximum instantaneous gbpc15 7.5a forward voltage drop per gbpc25 12.5a element at specified current gbpc35 17.5a v f 1.1 v maximum dc reverse current at rated dc blocking voltage per element i r 5 ua typical thermal resistance (note 1) r jc 1.5 / w operating and storage temperature range t j ,t stg -50 to +150 notes: 1. thermal resistance from junction to case. 2. suffix ?w? - wire lead structure/?m? - terminal location face to face.
- 695 - ratings and characteristic curves (gbpc25005 thru gbpc2510) gbpc35005 gbpc15005 gbpc3510 gbpc1510 fig.1- maximum forward current derating curve average for ward current . (a) 160 180 20 40 60 80 100 120 140 0 5 10 15 20 25 40 35 30 case temperature. ( c) o gbpc35 gbpc25 gbpc15 fig.2- maximum non-repetitive forward surge current per bridge element peak for ward surge current . (a) 1 234 1.5 5 6 9 8 710 25 20 15 30 100 60 40 80 20 100 300 400 200 number of cycles at 60hz gbpc35 gbpc25 gbpc15 fig.4- typical forward characteristics per bridge element instantaneous for ward current . (a) .6 .8 1.0 1.2 1.4 1.6 1.8 2.0 0.1 1 10 100 1000 forward voltage. (v) gbpc35 gbpc25 g b p c 15 fig.3- typical reverse characteristics per bridge element instantaneous reverse current .( a) 0 20 40 60 80 100 120 140 .10 1.0 10 100 percent of rated peak reverse voltage. (%) tj=25 c 0 tj=125 c 0
|
